Materials Science
epub |eng | | Author:Olga Zybina & Marina Gravit

The samples were tested in the mode of “standard fire”, in which the average furnace temperature, measured by installed thermocouples, was monitored and adjusted according to dependence [23]: where To ...
( Category: Materials Science November 5,2020 )
epub |eng | | Author:Unknown

4.1 Nanosuspension-Based Conventional Techniques Nanosuspensions (NSs) technology is a formulation approach suitable to improve solubility and bioavailability both of hydrophilic (H) and lipophilic (L) bioactive compounds (HBACs and LBACs). A ...
( Category: Materials Science August 7,2020 )
epub |eng | | Author:Amit Bhaduri

8.14.2 High Temperature As the temperature is increased above room temperature, the fatigue strength of metals generally decreases. A diagram of plastic strain amplitude , , versus number of cycles ...
( Category: Manufacturing August 6,2020 )
epub |eng | | Author:Udo W. Pohl

During surface diffusion the adatom encounters other atoms on the surface. The probability of such a meeting depends on the areal density of single migrating atoms, and the areal density ...
( Category: Materials Science July 26,2020 )
epub |eng | | Author:Sergio Rosales-Mendoza & Omar González-Ortega

CNTs-Based Vaccines Over the past three decades, the aquaculture industry has made impressive progress towards constituting a source of high quality protein for the worldwide population. However, viral and bacterial ...
( Category: Materials Science July 21,2020 )
epub |eng | 2012-03-18 | Author:Griffin, C.W.; Fricklas, Richard

TABLE 11.2 ASTM Standards for APP Modified Bitumen TABLE 11.3 ASTM Standards for SBS Modified Bitumen Figure 11.3 Propane torching of APP-modified-bitumen sheets is mandatory because APP-modified asphalt cannot be ...
( Category: Roofing July 21,2020 )
epub |eng | | Author:Branko L. Dokić & Branko Blanuša

(4.224) where L os is the total stray inductance of the secondary. The time during which the secondary voltage is zero and the choke voltage is –V o, is extended ...
( Category: Materials Science July 21,2020 )
epub |eng | | Author:Welding

8 + 1" – 1" 1" 4 16 4 106 CHAPTER 2 Figure 2.50 GMAW (spray transfer) workmanship qualification test Source: Courtesy of the American Welding Society Gas Metal Arc ...
( Category: Welding July 16,2020 )
epub |eng | | Author:Welding

Advanced Shielded Metal Arc Welding 103 As in Practice 3-10, tack weld the plates together with a root opening of 1/8 in. (3 mm) at one end and 1/2 in. ...
( Category: Welding July 16,2020 )
epub |eng | | Author:Vesna Žegarac Leskovar & Miroslav Premrov

A difference in the insulation properties of the wall elements, such as the insulation thickness, the number of insulating layers or the insulation type can be observed in the above ...
epub |eng | | Author:Thomas D. Rossing & Christopher J. Chiaverina

The Evolution of Digital Photography In a period of a little over 50 years, digital imaging has evolved from humble beginnings to a process used by billions of people around ...
( Category: Electricity July 7,2020 )
epub |eng | | Author:Jude Mary Runge

4.4 Microstructural Development in Wrought Aluminum Alloys Wrought alloys are designed to be deformed and therefore must possess a minimum ductility commensurate with the manufacturing process under consideration for engineering ...
( Category: Electricity July 7,2020 )
epub |eng | | Author:Zahra Trad, Abdelwahed Barkaoui, Moez Chafra & João Manuel R.S. Tavares

Roth, V. (1977). Two problems in articular biomechanics: I. Finite element simulation for contact problems of articulations, II. Age dependent tensile properties. Ph.D. thesis, Rensselaer Polytechnic Institute, Troy, New York. ...
( Category: Biomedical Engineering July 5,2020 )
epub |eng | | Author:Zoltán Kocsis & Etele Csanády

(2.77) wherex—is the length of the pellet out of the channel, mm. The instantaneous pushing force is (2.78) where σe—is the stress due to the stored elastic deformation (lateral pressure), ...
( Category: Materials Science July 5,2020 )
epub |eng | | Author:Jacob (Theo) Kloprogge

In soils, kaolinite is formed at pressure-temperature conditions of the Earth’s surface (i.e., 25–30 °C and atmospheric pressure). However, kaolinite also persists until late diagenesis at temperatures lower than 200 ...
( Category: Materials Science July 5,2020 )