epub |eng | 2012-07-24 | Author:Massad Ayoob [Ayoob, Massad]

Sheriff’s Model was rare in the gun’s original time, but proved reasonably popular in third generation of its manufacture. Note short barrel and absence of ejector rod assembly. .44-40 (.44 ...

epub |eng | 2011-04-25 | Author:Patrick Sweeney [Sweeney, Patrick]

The PRI Gas Buster has a lip on the bottom, to block gas puffs that might jet back into your face. You can clearly see the joint between the parts ...

epub, pdf |eng | 2019-04-10 | Author:David Nash

At one end of the training spectrum, they are considered “beginner’s guns” but taken to mastery they are the firearms of experts. I prefer revolvers for home defense, since a ...

epub |eng | 2008-05-30 | Author:Sweeney, Patrick [Sweeney, Patrick]

So unless you figured a way to modify your old 10mm magazine to lock into place in the new SF frame, your 10mm SF project would come screeching to a ...

epub |eng | 2011-03-21 | Author:Cornell, Joseph

GRADE III Discontinued 1984. NOTE: The Grade III was offered in two variations. The first was hand-engraved and produced in Belgium. The second was photo-etched and built in Belgium and ...

epub |eng | 2013-05-09 | Author:Roy C. McHenry

CHAPTER XVII. COLT hand-ejector pocket revolvers in .32 caliber had been made for about IS years and Smith & Wesson side-swingers had been on the market for four years in ...

epub |eng | 2011-05-12 | Author:Phillip Peterson [Peterson, Phillip]

Courtesy Paul S. Scarlata from Mannlicher Military Rifles, Andrew Mobray Publishers Model 1895 No. 1 Cavalry Carbine This model featured a half stock with no handguard and sling bars on ...

epub |eng | 2011-05-04 | Author:J.B. Wood

13. Drifting out the vertical pin will allow removal of the extractor and its coil spring. 14. With a proper roll-pin drift punch, drive out the cross-pin at the upper ...

epub |eng | | Author:Joseph Cornell

View a text version of this table MODEL 70 TARGET RIFLE This version is chambered for the .308 or the .30-06 cartridges. It was offered with a 24" heavy barrel ...

epub |eng | 2012-07-24 | Author:Tom Turpin [Turpin, Tom]

Function and Aesthetics The David Miller shop doesn’t turn out the plain-Jane round unadorned barrel on any of their rifles. The barrel treatment on each of the two Miller Co. ...

epub |eng | 2012-01-30 | Author:Eimer Ph D., Bruce N. [Eimer, Bruce N.]

CHAPTER 20 Concealment Holster Primer Holsters are basic equipment. You cannot safely carry a loaded handgun without an intelligently designed, comfortable, and functional holster that precisely fits your gun. Most ...

epub, azw3 |eng | | Author:Rick Hacker

Vernier tang sights are a popular feature on Sharps rifles, whether replicas or originals. This early Shiloh Sharps is stamped with the original Farmington, New York, address that is sought ...

epub |eng | 2012-05-01 | Author:Joe Kertzman [Kertzman, Joe]

OXYGEN/ACETYLENE TORCH The oxygen/acetylene (A/E) torch is an excellent source of heat for the quenching process and one that I used for many years. I have used it to harden ...

epub |eng | 2010-08-27 | Author:Patrick Sweeney [Sweeney, Patrick]

Today you can have a Dillon (or other brand) progressive reloader with case feeder, bullet feeder, and produce buckets of practice ammo. No need to slave in the basement all ...

epub |eng | 2011-11-11 | Author:Kevin Muramatsu [Muramatsu, Kevin]

13. Hold the trigger back to remove sear tension from the hammer, and push out the hammer pivot cross pin. Remove the hammer assembly upward. The bolt latch spring encircles ...